<h2>CHAPTER IX.</h2>
<h3>TENTS.—ARMY SHELTER-TENT (<i>tente d'abri</i>).</h3>
<p>The shelter-tent used by the Union soldiers during the Rebellion was
made of light duck<SPAN name="FNanchor_12_12" id="FNanchor_12_12"></SPAN><SPAN href="#Footnote_12_12" class="fnanchor">[12]</SPAN> about 31-1/2 inches wide. A tent was made in two
pieces both precisely alike, and each of them five feet long and five
feet and two inches wide; i.e., two widths of duck. One of these pieces
or half-tents was given to every soldier. That edge of the piece which
was the bottom of the tent was faced at the corners with a piece of
stouter duck three or four inches square. The seam in the middle of the
piece was also faced at the bottom, and eyelets were worked at these
three places, through which stout cords or ropes could be run to tie
this side of the tent down to the tent-pin, or to fasten it to whatever
else was handy. Along the other three edges of each piece of tent, at
intervals of about eight inches, <span class="pagenum"><SPAN name="Page_73" id="Page_73">[Pg 73]</SPAN></span>were button-holes and buttons; the
holes an inch, and the buttons four inches, from the selvage or hem.<SPAN name="FNanchor_13_13" id="FNanchor_13_13"></SPAN><SPAN href="#Footnote_13_13" class="fnanchor">[13]</SPAN></p>
<p>Two men could button their pieces at the tops, and thus make a tent
entirely open at both ends, five feet and two inches long, by six to
seven feet wide according to the angle of the roof. A third man could
button his piece across one of the open ends so as to close it, although
it did not make a very neat fit, and half of the cloth was not used;
four men could unite their two tents by buttoning the ends together,
thus doubling the length of the tent; and a fifth man could put in an
end-piece.</p>
<p>Light poles made in two pieces, and fastened together with ferrules so
as to resemble a piece of fishing-rod, were given to some of the troops
when the tents were first introduced into the army; but, nice as they
were at the end of the march, few soldiers would carry them, nor will
you many days.</p>
<p>The tents were also pitched by throwing them over a tightened rope; but
it was easier to <i>cut</i> a stiff pole than to <i>carry</i> either the pole or
rope.</p>
<p>You need not confine yourself exactly to the dimensions of the army
shelter-tent, but for a <span class="pagenum"><SPAN name="Page_74" id="Page_74">[Pg 74]</SPAN></span>pedestrian something of the sort is necessary
if he will camp out. I have never seen a "shelter" made of <i>three</i>
breadths of drilling (seven feet three inches long), but I should think
it would be a good thing for four or five men to take.<SPAN name="FNanchor_14_14" id="FNanchor_14_14"></SPAN><SPAN href="#Footnote_14_14" class="fnanchor">[14]</SPAN> And I should
recommend that they make three-sided end-pieces instead of taking
additional half-tents complete, for in the latter case one-half of the
cloth is useless.</p>
<p>Five feet is <i>long</i> enough for a tent made on the "shelter" principle;
when pitched with the roof at a right angle it is 3-1/2 feet high, and
nearly seven feet wide on the ground.</p>
<p>Although a shelter-tent is a poor substitute for a house, it is as good
a protection as you can well carry if you propose to walk any distance.
It should be pitched neatly, or it will leak. In <span class="pagenum"><SPAN name="Page_75" id="Page_75">[Pg 75]</SPAN></span>heavy, pelting rains a
fine spray will come through on the windward side. The sides should set
at right angles to each other, or at a sharper angle if rain is
expected.</p>
<p>There are rubber blankets made with eyelets along the edges so that two
can be tied together to make a tent; but they are heavier, more
expensive, and not much if any better; and you will need other rubber
blankets to lie upon.</p>
<p>If you wish for a larger and more substantial covering than a "shelter,"
and propose to do the work yourself, you will do well to have a
sailmaker or a tent-maker cut the cloth, and show you how the work is to
be done. If you cannot have their help, you must at least have the
assistance of one used to planning and cutting needle-work, to whom the
following hints may not be lost. We will suppose heavy drilling 29-1/2
inches wide to be used in all instances.</p>
<h3>THE A-TENT.</h3>
<p>To make an A-tent,<SPAN name="FNanchor_15_15" id="FNanchor_15_15"></SPAN><SPAN href="#Footnote_15_15" class="fnanchor">[15]</SPAN> draw upon the floor a straight line seven feet
long, to represent the upright pole or height of the tent; then draw a
line at right angles to and across the end of the first one, to
represent the ground or bottom of the tent. Complete the plan by finding
where the corners will be on the ground line, <span class="pagenum"><SPAN name="Page_76" id="Page_76">[Pg 76]</SPAN></span>and drawing the two sides
(roof) from the corners<SPAN name="FNanchor_16_16" id="FNanchor_16_16"></SPAN><SPAN href="#Footnote_16_16" class="fnanchor">[16]</SPAN> to the top of the pole-line. This triangle
is a trifle larger than the front and back of the tent will be.</p>
<p>The cloth should be cut so that the twilled side shall be the outside of
the tent, as it sheds the rain better.</p>
<p>Place the cloth on the floor against the ground-line, and tack it (to
hold it fast) to the pole-line, which it should overlap 3/8 of an inch;
then cut by the roof-line. Turn the cloth over, and cut another piece
exactly like the first; this second piece will go on the back of the
tent. Now place the cloth against the ground-line as before, but upon
the other side of the pole, and tack it to the floor after you have
overlapped the selvage of the piece first cut 3/4 of an inch. Cut by the
roof-line, and turn and cut again for the back of the tent.</p>
<p>In cutting the four small gores for the corners, you can get all the
cloth from one piece, and thus save waste, by turning and tearing it in
two; these gore-pieces also overlap the longer breadths 3/4 of an inch.</p>
<p>The three breadths that make the sides or roof are cut all alike; their
length is found by <span class="pagenum"><SPAN name="Page_77" id="Page_77">[Pg 77]</SPAN></span>measuring the plan from corner to corner over the
top; in the plan now under consideration, the distance will be nearly
sixteen feet. When you sew them, overlap the breadths 3/4 of an inch the
same as you do the end-breadths.</p>
<p>In sewing you can do no better than to run, with a machine, a row of
stitching as near each selvage as possible; you will thus have two rows
to each seam, which makes it strong enough. Use the coarsest cotton, No.
10 or 12.</p>
<p>The sides and two ends are made separately; when you sew them together
care must be taken, for the edges of the ends are cut cross-grained, and
will stretch very much more than the cloth of the sides (roof). About as
good a seam as you can make, in sewing together the sides and ends, is
to place the two edges together, and fold them outwards (or what will be
downwards when the tent is pitched) twice, a quarter of an inch each
time, and put two rows of stitching through if done on a machine, or one
if with sail-needle and twine. This folding the cloth six-ply, besides
making a good seam, strengthens the tent where the greatest strain
comes. It is also advisable to put facings in the two ends of the top of
the tent, to prevent the poles from pushing through and chafing.</p>
<p>The bottom of the tent is completed next by folding upwards and inwards
two inches of cloth <span class="pagenum"><SPAN name="Page_78" id="Page_78">[Pg 78]</SPAN></span>to make what is called a "tabling," and again
folding in the raw edge about a quarter of an inch, as is usual to make
a neat job. Some makers enclose a marline or other small tarred rope to
strengthen the foot of the tent, and it is well to do so. One edge of
what is called the "sod-cloth" is folded in with the raw edge, and
stitched at the same time. This cloth, which is six to eight inches
wide, runs entirely around the bottom of the tent, excepting the
door-flap, and prevents a current of air from sweeping under the tent,
and saves the bottom from rotting; the sod-cloth, however, will rot or
wear out instead, but you can replace it much more easily than you can
repair the bottom of the tent; consequently it is best to put one on.</p>
<p>One door is enough in an A-tent; but, if you prefer two, be sure that
one at least is nicely fitted and well provided with tapes or buttons,
or both: otherwise you will have a cheerless tent in windy and rainy
weather. The door-flap is usually made of a strip of cloth six to nine
inches wide, sewed to the selvage of the breadth that laps inside; the
top of it is sewed across the inside of the other breadth, and reaches
to the corner seam. Tent-makers usually determine the height of the door
by having the top of the flap reach from selvage to seam as just
described; the narrower the flap <span class="pagenum"><SPAN name="Page_79" id="Page_79">[Pg 79]</SPAN></span>is, the higher the door will be. Some
make the door-flap considerably wider at the bottom than at the top, and
thus provide against the many annoyances that arise from one too narrow.</p>
<p>The loops (or "beckets" as they are called) that fasten to the tent-pins
are put in one at each side of the door and at every seam. Some makers
work an eyelet or put a grommet in the seam; but, in the army-tents
which are made of duck, there are two eyelets worked, one on each side
of the seam, and a six-thread manilla rope is run through and held in by
knotting the ends.</p>
<p>The door is tied together by two double rows of stout tapes<SPAN name="FNanchor_17_17" id="FNanchor_17_17"></SPAN><SPAN href="#Footnote_17_17" class="fnanchor">[17]</SPAN> sewed on
at intervals of about eighteen inches; one inside the tent ties the
door-flap to the opposite breadth, and a second set outside pulls
together the two selvages of the centre breadths. Do not slight this
work: a half-closed door, short tapes, and a door-flap that is slapping
all the time, are things that will annoy you beyond endurance.</p>
<p>The upright poles of a tent such as has been described should be an inch
or two more than seven feet, for the cloth will stretch. If you have a
sod-cloth, the poles should be longer still.<SPAN name="FNanchor_18_18" id="FNanchor_18_18"></SPAN><SPAN href="#Footnote_18_18" class="fnanchor">[18]</SPAN></p>
<p><span class="pagenum"><SPAN name="Page_80" id="Page_80">[Pg 80]</SPAN></span></p>
<h3>THE WALL-TENT.</h3>
<p>The wall-tent is shaped like a house: the walls or sides, which are
perpendicular, are four feet high. A continuous piece of cloth runs from
the ground to the eaves, thence on toward the ridgepole, and down the
other side to the ground. The tent is made on the same general
principles as the one last described. It is four breadths square, but
the width is usually diminished about one foot by cutting six inches
from each corner breadth. If the cloth is drilling or light duck, you
can overlap the centre breadths a foot, and thus have the doors
ready-made.</p>
<p>Draw a plan upon the floor as in the other case; the pole nine feet and
two inches high, the corners four breadths apart less the overlappings
and the narrowing; draw the wall (in the plan only) four feet and two
inches high. The roof-line runs of course from the top of the pole to
the top of the wall.</p>
<p>Cut the cloth, as before, so as to have the twilled side out. Add six
inches to the distance measured on the plan, for the length of the walls
and roof, so as to get cloth for the eaves.</p>
<p>The wall is to be four feet high; consequently, when you have sewed
together the four breadths that make the roof and walls, measure four
feet 3-1/2 inches from the ends (bottoms), double the <span class="pagenum"><SPAN name="Page_81" id="Page_81">[Pg 81]</SPAN></span>cloth, and sew
two rows of stitching by hand across from side to side, 1-1/2 inches
from the doubling; this makes the tabling for the eaves, and you have
two inches left for the bottom tabling. Use stout twine for these seams
at the eaves, and take only three to four stitches to the inch.</p>
<p>Take the same care as before in sewing together the ends and sides; the
larger the tent, the more this difficulty increases.</p>
<p>The sod-cloth becomes more of a necessity as we increase the size of the
tent, and add to the difficulty of making it fit snugly to the ground.</p>
<p>Facings should be put in where the ends of the poles bear, as before
explained; and also in the four upper corners of the wall, to prevent
the strain of the corner guy-lines from ripping apart the eaves and
wall.</p>
<p>Beckets must be put in the bottom of each seam and the door, the same as
in the A-tent, and strong tapes sewed to the door.</p>
<p>Guy-lines made of six-thread manilla rope are put in at the four corners
of the eaves, and at every seam along that tabling, making five upon
each side. Work an eyelet, or put a grommet, in the doubled cloth of the
seam; knot the end of the guy-line to prevent its pulling through: tying
the rope makes too bungling a <span class="pagenum"><SPAN name="Page_82" id="Page_82">[Pg 82]</SPAN></span>job, and splicing it is too much work.
The six guy-lines in the body of the tent should be about nine feet
long, the four corner ones about a foot longer. The fiddles<SPAN name="FNanchor_19_19" id="FNanchor_19_19"></SPAN><SPAN href="#Footnote_19_19" class="fnanchor">[19]</SPAN> should
be made of some firm wood: pine and spruce will not last long enough to
pay for the trouble of making them.</p>
<p>The poles should be nine feet and four or five inches long. If they are
too long at first, sink the ends in the ground, and do not cut them off
until the tent has stretched all that it will.</p>
<p>In permanent camp a "fly" over the tent is almost indispensable for
protection from the heat and pelting rains. It should be as long as the
roof of the tent, and project at least a foot beyond the eaves. The
guy-lines should be a foot or more longer than those of the tent, so
that the pins for the fly may be driven some distance outside those of
the tent, and thus lift the fly well off the roof.</p>
<h3>CLOTH FOR TENTS.</h3>
<p>For convenience we have supposed all of the tents to be made of heavy
drilling. Many tent-<span class="pagenum"><SPAN name="Page_83" id="Page_83">[Pg 83]</SPAN></span>makers consider this material sufficiently strong,
and some even use it to make tents larger than the United States army
wall-tent. My own experience leads me to recommend for a wall-tent a
heavier cloth, known to the trade as "eight-ounce Raven's" duck,<SPAN name="FNanchor_20_20" id="FNanchor_20_20"></SPAN><SPAN href="#Footnote_20_20" class="fnanchor">[20]</SPAN>
because drilling becomes so thin after it has been used two or three
seasons that a high wind is apt to tear it.</p>
<p>The cost of the cloth is about the same as the value of the labor of
making the tent; but the difference between the cost of drilling and
eight-ounce duck for a wall-tent of four breadths with a fly is only
three to four dollars, and the duck tent will last nearly twice as long
as the one of drilling. For these reasons it seems best not to put your
labor into the inferior cloth.</p>
<p>Before you use the tent, or expose to the weather any thing made of
cotton cloth, you should wash it thoroughly in strong soap-suds, and
then soak it in strong brine; this takes the sizing and oil out of the
cloth, and if repeated from year to year will prevent mildew, which soon
spoils the cloth. There are mixtures that are said to be better still,
but a tent-maker <span class="pagenum"><SPAN name="Page_84" id="Page_84">[Pg 84]</SPAN></span>assures me that the yearly washing is better than any
thing applied only once. Some fishermen preserve their sails by soaking
them in a solution of lime and water considerably thinner than
whitewash. Others soak them in a tanner's vat; but the leather-like
color imparted is not pleasing to the eye. Weak lime-water they say does
not injure cotton; but it ruins rope and leather, and some complain that
it rots the thread.</p>
<p>It will save strain upon any tent, to stay it in windy weather with
ropes running from the iron pins of the upright poles (which should
project through the ridgepole and top of the tent) to the ground in
front and rear of the tent. A still better way is to run four ropes from
the top—two from each pole-pin—down to the ground near the tent-pins
of the four corner guy-lines. The two stays from the rear pole should
run toward the front of the tent; and the two front stays toward the
rear, crossing the other two. The tent is then stayed against a wind
from any quarter, and the stays and guy-lines are all together on the
sides of the tent.</p>
<p>Loosen the stays and guy-lines a little at night or when rain is
approaching, so as to prevent them from straining the tent by shrinking.</p>
<p>Around the bottom of any tent you should dig a small trench to catch and
convey away the <span class="pagenum"><SPAN name="Page_85" id="Page_85">[Pg 85]</SPAN></span>water when it rains; and I caution you against the
error which even old campers sometimes make,—do not try to have the
water run up hill.</p>
<h3>HOW TO PITCH A WALL-TENT QUICKLY.</h3>
<p>After you have once pitched the tent, and have put the poles and pins in
their exact places, note the distance from one of the upright poles to
the pin holding one of the nearest corner guy-lines, and then mark one
of the poles in such a way that you can tell by it what that distance
is. When you next wish to pitch the tent, drive two small pins in the
ground where the two upright poles are to rest,—the ridgepole will tell
you how far apart they must be,—then, by measuring with your marked
pole, you can drive the four pins for the corner guys in their proper
places.</p>
<p>Next spread the tent on the ground, and put the ridgepole in its place
in the top of the tent, and the two upright poles in their places. Then
raise the tent. It will take two persons, or, if the tent is large, four
or more, having first moved it bodily, to bring the feet of the upright
poles to touch the two small pins that you drove at the beginning. You
can now catch and tighten the corner guy-lines on the four pins
previously driven. In driving the other pins, it looks well to have them
on a line, if possible; also try to <span class="pagenum"><SPAN name="Page_86" id="Page_86">[Pg 86]</SPAN></span>have the wall of the tent set
square: to do this you must tie the door just right before you tighten a
guy-line.</p>
<p>You will find this way of pitching a tent convenient when a wind is
blowing, or when your assistant is not a strong person. If the wind is
very high, spread your tent to windward, and catch the windward
guy-lines before raising the tent. You will thus avoid having it blown
over.</p>
<h3>TENT-POLES.</h3>
<p>As tent-poles are not expensive, you may find it convenient to have two
sets for each tent; one stout set for common use, and a lighter set to
take when transportation is limited. Sound spruce, free from large knots
and tolerably straight-grained, makes good poles; pine answers as well,
but is more expensive.</p>
<p>The upright poles of a stout set for a wall-tent of the United States
Army pattern should be round or eight-sided, and about two inches in
diameter.<SPAN name="FNanchor_21_21" id="FNanchor_21_21"></SPAN><SPAN href="#Footnote_21_21" class="fnanchor">[21]</SPAN> If you prefer to have them square, round off the edges, or
they will be badly bruised upon handling. Drive a stout iron pin<SPAN name="FNanchor_22_22" id="FNanchor_22_22"></SPAN><SPAN href="#Footnote_22_22" class="fnanchor">[22]</SPAN>
seven or eight inches long into the centre of the top until <span class="pagenum"><SPAN name="Page_87" id="Page_87">[Pg 87]</SPAN></span>it projects
only about three and a half or four inches, or enough to go through the
ridgepole and an inch beyond. It will be necessary to bore a hole in the
pole before driving in the pin, to prevent splitting. A ferrule is also
serviceable on this end of the pole.</p>
<p>The ridgepole should be well rounded on the edges, and be about two and
a half inches wide and two inches thick. If made of stuff thinner than
an inch and a half, it should be wider in the middle than above stated,
or the pole will sag. Bore the holes to receive the pins of the uprights
with an auger a size larger than the pins, so that they may go in and
out easily: these holes should be an inch and a half from the ends.
Ferrules or broad bands are desirable on the ends of the ridgepole; but
if you cannot afford these you may perhaps be able to put a rivet or two
through the pole between the ends and the holes, or, if not rivets, then
screws, which are better than nothing to prevent the pin of the upright
from splitting the ridgepole.</p>
<h3>TENT-PINS.</h3>
<div class="figleft"> <ANTIMG src="images/p88.png" width-obs="26" height-obs="100" alt="Tent pin" title="Tent pin" /></div>
<p>Tent-pins should be made of sound hard wood; old wheel-spokes are
excellent. Make them pointed at the bottom, so that they will drive
easily; and notch them about two inches from the top, so that they will
hold the rope. Cut away the wood from just above the notch <span class="pagenum"><SPAN name="Page_88" id="Page_88">[Pg 88]</SPAN></span>towards the
back of the head; this will prevent the notch of the pin from splitting
off when it is driven. It is well to have pins differ in length and
size: those for the corners and the stays should be the largest, say
fifteen to eighteen inches long; and those for the wall and door may be
eight or ten inches. But pins of these sizes are apt to pull out in a
heavy storm; and so when you are to camp in one spot for some time, or
when you see a storm brewing, it is well to make pins very stout, and
two feet or more long, for the stays and four corner guy-lines, out of
such stuff as you find at hand.</p>
<p>Loosen the pins by striking them on all four sides before you try to
pull them up. A spade is a fine thing to use to pry out a pin that is
deep in the ground, and a wooden mallet is better than an axe or hatchet
to drive them in with; but, unless you have a large number of pins to
drive, it will hardly pay you to get a mallet especially for this
business.</p>
<p>Make a stout canvas bag to hold the tent-pins; and do not fold them
loose with the tent, as it soils and wears out the cloth.</p>
<h3>BEST SIZE OF TENTS.</h3>
<p>The majority of people who go into permanent camp prefer tents
considerably larger than the <span class="pagenum"><SPAN name="Page_89" id="Page_89">[Pg 89]</SPAN></span>army wall-tent; but, unless your camp is
well sheltered from the wind, you will have constant and serious
troubles during every gale and thunder-storm, if you are in a large or
high tent. A large tent is certainly more comfortable in fine weather;
but you can make a small one sufficiently cheerful, and have a sense of
security in it that you cannot feel in one larger. But, if you will have
a large tent, make it of something heavier than drilling.</p>
<p>If you have two tents of the same height, you can connect the tops with
a pole, and throw a fly, blanket, or sheet over it on pleasant days.</p>
<p>Do not pack away a tent when it is damp if you can possibly avoid it, as
it will mildew and decay in a few days of warm weather. If you are
compelled to pack it when very damp, you can prevent decay by salting it
liberally inside and out.</p>
<p>Before you put away your tent for the season be sure that it is
perfectly dry, and that the dead flies and grasshoppers are swept out of
the inside. You should have a stout bag to keep it in, and to prevent
its being chafed and soiled when it is handled and carried. You will
find a hundred good uses for the bag in camp.<span class="pagenum"><SPAN name="Page_90" id="Page_90">[Pg 90]</SPAN></span></p>
<hr style="width: 65%;" />
<div style="break-after:column;"></div><br />